Home / Posts, Clay and Tension: The Order of Work Behind a Chain Link Fence That Stays Straight
Posts, Clay and Tension: The Order of Work Behind a Chain Link Fence That Stays Straight

A chain link fence either stays straight for decades or leans within a few seasons, and the difference is usually settled in the first two days of work, before any fabric is unrolled. The sequence matters more than the materials. Done in the right order, a basic galvanized fence outlasts a rushed one built from better parts.
Start with 811, the Property Line and the Covenants
Digging comes last in the planning stage, not first. Call 811 a few business days ahead and wait for the utility marks. Back lot lines are exactly where cable, gas and irrigation lines tend to run, so a fence line that looks empty often is not.
Next, confirm where the line actually is. A plat or survey and the corner pins give a real answer; a neighbor's old fence does not. Many Edmond subdivisions also carry HOA covenants that limit fence height, material or coating color, so read them before ordering anything. Returning a truckload of black vinyl coated fabric is a bad way to learn a rule.
For the layout side of the job, this guide to chain link planning on the same site is the place to start before material is ordered.
Terminal Posts Go In First
Terminal posts are the corners, the ends and the gate posts. They go in first, and then a tight string line is pulled between them at the top and again near the bottom. Every line post is set to that string, which is the only reason a long run looks straight.
The two post types do different work:
| Post type | Job | Common mistake | |---|---|---| | Terminal (corner, end, gate) | Carries all the fabric tension | Using line post pipe at a corner, which then leans inward | | Line | Holds the fabric and top rail in plane | Spacing wider than about 10 feet, so the fabric bellies |
Terminal pipe is larger in diameter and heavier in wall for a reason. Line posts barely feel the pull. Corners feel all of it.
A worked example shows the count. A 60 foot side run between two corner posts, kept to 10 foot spacing or less, makes six equal bays and needs five line posts between the terminals. Splitting the distance evenly beats setting nine posts at 10 feet and leaving one odd gap at the end.
Footings in Red Clay
Holes run about three times the post diameter. A common rule of thumb for a 4 foot fence is line posts roughly 2 feet deep, with terminal and gate holes deeper and wider than that.
Edmond sits on expansive red clay that shrinks in drought and swells when wet. That movement, more than any single bad install, is what loosens and jacks posts over the years. Two details in the footing help:
- Belled, not mushroomed. A footing wider at the bottom resists being lifted. One that flares wider at the top gives swelling clay a shelf to push up on.
- Concrete on firm soil. In tight clay, a deep gravel layer in the bottom of the hole can hold water like a bathtub around the post base instead of draining it. Pouring concrete directly on firm, undisturbed soil is usually the better choice here.
Deeper concrete alone does not guarantee a post will never move in clay, but a well-shaped footing slows the movement considerably.
Finish each footing with a crown that slopes away from the post and sits slightly above grade. Standing water at the base is where galvanized pipe rusts first.
Let the Concrete Cure Before Pulling Anything
Several days of cure time come before any stretching. Pulling tension against green concrete can tip a terminal post out of plumb, and it does not spring back. This is the step most often skipped when a crew is trying to finish in a weekend.
Hardware, in Order
On each terminal post, the hardware goes on in sequence:
- Tension bands, one per foot of fabric height minus one. A 4 foot fence takes 3.
- A brace band.
- Rail end cups.
- The post cap.
Line posts get loop caps, and the top rail passes through them. Rail sections join with swedged (tapered) ends or sleeves and run continuously through the loops. Cut the last piece so it seats fully in the end cup.
Choosing and Hanging the Fabric
Gauge numbers run backward. A lower number is thicker wire, so nine gauge is heavier than 11 or 11.5 gauge. Mesh size matters as well: smaller diamonds are harder to climb and stronger per foot.
On a residential fence, the knuckled (bent over) selvage goes on top. A barbed top edge in a backyard is a hazard to kids, pets and hands.
Hang the fabric on the outside face of the posts, the side facing away from the yard being enclosed. That way it cannot be pushed off the posts from the outside.
Stretching, Step by Step
- Weave a tension bar through the first row of diamonds and bolt it to the tension bands.
- Unroll the fabric along the line toward the far end.
- Weave a second bar at the far end and pull with a stretcher bar and come-along.
- Stop when the diamonds narrow slightly and the fabric gives only a little under a hand squeeze.
- Make the far-end connection, then release the tool.
Over-stretching distorts the mesh and drags corners inward. If there is excess, untwist the knuckles at the top and bottom of one picket and spin that picket out. Cutting across with a grinder leaves loose ends that unravel.
Ties
Wire ties go on line posts roughly every foot, and on the top rail roughly every two feet. Turn the ends inward so they do not cut anyone reaching over or along the fence.
The Bottom Edge, Slopes and Gates
Run a bottom tension wire or a bottom rail. Without one, dogs push the fabric out at the base and the bottom edge curls. Keep a small, consistent gap above grade and fill dips with soil rather than leaving open gaps.
On sloped lots, keep posts plumb and let the fabric follow the grade. Chain link racks to fit slopes well, so it handles uneven yards better than most fence types. Steep changes may still call for stepped sections or a custom cut.
Gate posts should be the heaviest on the job and set the deepest, since a swinging gate levers on them every day. Measure the opening between posts with hinge and latch clearance in mind. Install the bottom hinge pin pointing up and the top hinge pin pointing down, so the gate cannot simply be lifted off.
Decide on Slats Before the Posts Go In
Bare chain link lets wind pass through. Privacy slats or windscreen turn it into a sail, which matters in central Oklahoma, where severe thunderstorm winds are routine. Adding slats changes what the posts must handle. If slats are planned, upsize the posts, shorten the spacing, or both, at the time of installation. Retrofitting heavier posts later means digging everything out.
Keeping It Straight Afterward
Chain link is low maintenance, not no maintenance. Two habits protect the finish:
- Coat any field cut on galvanized pipe with cold galvanizing compound.
- Keep string trimmers away from the base of posts. They chew through vinyl coating, and once the coating is breached, rust can start underneath. A mow strip or careful trimming prevents it. Vinyl coated fabric can still rust where the coating is damaged.
Walk the fence line once a year, and again after a very wet spring or a long drought, since both swing the clay. Check that posts are plumb, tighten the tension band bolts and replace missing ties. Pull out vines and Bermuda grass growing into the mesh, because they hold moisture against the wire and add weight.
Anyone comparing contractors or materials can use a fences edmond review style checklist built from these steps: string line, terminal pipe size, footing shape, cure time and stretch method. A crew that can answer each one plainly has likely built a fence that will still be standing straight in ten years.