Edmond Fence Hub

Home / Chain Link Fence Myths That Shorten a Fence's Life, and the Facts That Fix Them

Chain Link Fence Myths That Shorten a Fence's Life, and the Facts That Fix Them

Vibrant autumn leaf caught in a chain link fence against a warm, golden in Edmond, OK

A thicker wire has a lower gauge number, and that single fact trips up more chain link buyers than any other. The belief that a bigger number means stronger fabric is one of several that quietly shorten the life of a fence. The rest of this page sorts the common myths from the facts, with a worked example of fixing a sagging run.

An earlier article on the site gives more detail on chain link parts and terms, so the focus here stays on what people get wrong.

Myth: A higher gauge number means stronger wire

Gauge runs backwards. A 9 gauge wire is heavier and stiffer than 11 or 11.5 gauge. Many light residential rolls fall in the 11 to 11.5 range, which is fine for a quiet side yard. Where a large dog leans on the fence or kids climb it, heavier wire earns its place.

Mesh size matters too. Standard 2 inch mesh gives easy footholds for climbing. A smaller mesh offers fewer of them, which helps if a climbing pet is the concern.

Myth: Galvanized, aluminized and vinyl coated are all the same protection

They are not interchangeable, and the label deserves a question before buying.

| Fabric type | What protects the wire | Worth knowing | |---|---|---| | Galvanized, zinc coated before weaving | Zinc applied to the wire, then woven | Cut and bent points can have thinner coverage | | Galvanized, zinc coated after weaving | Zinc applied to the finished fabric | Covers cut ends and twists more completely | | Aluminized | Aluminum coating instead of zinc | A different material, not a rebrand of galvanized | | Vinyl coated (black or green) | Polymer jacket over a metal core wire | The core can rust wherever the jacket is cut |

The vinyl row is where the myth lives. Vinyl coated chain link can rust. A trimmer line, a mower or a falling limb can slice the jacket, and the core wire starts to corrode at that spot, hidden under the color.

Myth: Posts are posts, so size does not matter

Terminal posts (corners, ends and gate posts) carry the full pull of the stretched fabric. They should be a larger diameter and heavier wall than the line posts between them. When line posts match the terminals in size, that often means the terminals are undersized for the job.

Spacing is the other half. Line posts about 10 feet apart or closer keep fabric from bellying. Wider spans sag sooner, especially along a long run that catches wind.

Every terminal also needs bracing: a horizontal brace rail plus a diagonal truss rod. Without both, terminal posts lean toward the run over time and the whole line goes slack.

Myth: Concrete around a post means it will never move

Concrete helps, but it does not guarantee anything. Edmond sits on red clay that swells when wet and shrinks and cracks in summer drought. That cycle can slowly tilt posts or jack them upward.

Footing shape makes a difference:

  • Straight sided footings, or ones slightly wider at the bottom, resist lifting.
  • A concrete "mushroom" that flares wide at ground level gives swelling clay more surface to grip and heave.
  • The top of each footing should be crowned so water runs away from the post. A dished top holds water at the base, and rust starts exactly where steel meets concrete.

Myth: Chain link is maintenance free

Nothing about a fence in a clay, sprinkler-fed, Bermuda grass yard stays maintenance free. The wear tends to come from a few predictable sources.

Water and soil

Fabric that sits in red clay or mulch stays wet, stains orange and loses its coating faster than the rest of the fence. Keeping the bottom edge a couple of inches above grade avoids that. Lawn sprinklers that hit the fence every day keep the lower fabric and post bases wet, and fertilizer overspray adds salts. Aiming heads away from the fence line costs nothing.

Grass and vines

Bermuda grass creeps through and along chain link. Trimming it with string line strips zinc and vinyl from the lower wires. A mowing strip or a narrow, edged mulch band reduces how often a trimmer has to touch the wire.

Woody vines such as trumpet vine and honeysuckle add weight, trap moisture against the metal and pry ties loose as the stems thicken. Light annual vines do far less harm.

Small parts

Fabric should be tied to the line posts and top rail at regular intervals along each. Aluminum ties do not rust, but they are softer. After storms, look for loose or missing ties, since fabric that flaps free wears through quickly.

Myth: Privacy slats are a simple bolt-on

Bare chain link lets wind pass through, a real advantage in Oklahoma's straight line winds. Slats or windscreen turn the fence into a sail. That added load calls for heavier posts, closer spacing and deeper footings than plain fabric needs. Retrofitting slats onto a light fence is a common reason runs start to lean. Chain link, with or without slats, should not be expected to survive a tornado or any severe wind.

Myth: Any chain link fence will contain any dog

Two details decide most escapes. A bottom tension wire, or a bottom rail, keeps the lower edge taut and harder to push under. Without one, the bottom edge curls outward after a few seasons of pushing and wind. The top edge finish matters for safety: a knuckled selvage folds the wire ends back with no sharp points, while a twisted selvage leaves points that can cut hands and pets. Knuckled top and bottom is the safer choice around kids and dogs. Even then, a determined digger or climber can beat a basic fence.

Myth: A sagging gate means the gate is the problem

Gate sag usually begins at the hinge post. A light hinge post that leans, or a gate frame without bracing, lets the latch side drop. Check that the hinge post is plumb before touching the hinges, or the adjustment will not last.

Worked example: taking the slack out of a sagging run

A run that bellows between posts can often be re-tensioned without replacing the fabric. The sequence for one section:

  1. Loosen the tension bands on the terminal post.
  2. Hook a fence stretcher bar a few feet into the fabric, then draw it tight with a come along anchored to the opposite terminal.
  3. Remove the extra slack by unthreading one picket wire, which separates the excess fabric.
  4. Reinsert the tension bar and retighten the bands.
  5. Re-tie the fabric to the line posts and top rail.

Splicing a damaged section follows the same logic. Cut out the damaged fabric, set a new piece of matching height and mesh size, and weave a single picket wire down through both edges to join them. Match the gauge and coating, or the patch will rust or sag differently from the rest. After any cut, touch up the bare ends of rail, posts and fabric with a cold galvanizing compound to slow rust.

After the ice and before the shovel

Ice storms, like the one that hit the Oklahoma City metro in October 2020, bring down limbs that crush top rails and bend posts. After an ice event, walk every section under a tree canopy. Look for kinked rail, sleeves pulled apart and posts that have rotated in their footings.

Before setting any new post, call 811 a few days ahead so buried utilities get marked. Confirm the property line from a survey or plat rather than trusting an old fence. In a subdivision, read the HOA covenants for style or color limits before buying material.

A yearly walk-around that catches problems early

  • Push each post and check for movement.
  • Sight down the top rail for dips.
  • Look for orange staining at post bases and along the bottom wire.
  • Confirm gate latches still meet without lifting.

Readers who want to compare notes on local fence conditions can find more of this kind of material on fences edmond review, where the emphasis stays on what holds up over seasons rather than what looks good on installation day.